C65100

Electrical Conduit, Pole Line Hardware, Motor, Rotor Bars
Fasteners Bolts, Cable Clamps, Cap Screws, Machine Screws, Nuts, Rivets, U Bolts, Fasteners, Screws
Industrial Oil Refinery Plumbing Tube, Heat Exchanger Tube, Welding Rod, Hydraulic Pressure Lines
Marine Hardware

Similar or Equivalent Specification

CDA	ASTM	ASARCON	SAE	AMS	Federal	Ingot#	Military	Other Desc
C65100	ASTM B98							LOW-SILICON BRONZE B

Cu%	Sn%	Pb%	Zn%	Fe%	Ni%	Sb%	P%	S%	Al%	Mn%	Si%
Note: Single values represent maximums.
REMAINDER		0.05	1.50	0.80	N/A					0.70	0.80-2.00

H02 HALF HARD TEMPER

SIZE RANGE: UP TO 1/2" INCLUSIVE ROD

Tensile Strength (min)		Yield Strength (at .5% extention under load min)		Elongation (in 2in. or 50mm min, %)	Brinell Hardness (min)	Remarks
Ksi	MPa	Ksi	MPa
55	380	20	140	11	N/A

SIZE RANGE: OVER 1/2" TO 2" INCLUSIVE ROD

Tensile Strength (min)		Yield Strength (at .5% extention under load min)		Elongation (in 2in. or 50mm min, %)	Brinell Hardness (min)	Remarks
Ksi	MPa	Ksi	MPa
55	380	20	140	12	N/A

SIZE RANGE: UP TO 1/2" INCLUSIVE ROD

Tensile Strength (min)		Yield Strength (at .5% extention under load min)		Elongation (in 2in. or 50mm min, %)	Brinell Hardness (min)	Remarks
Ksi	MPa	Ksi	MPa
65	450	35	240	8	N/A

SIZE RANGE: OVER 1/2" TO 2" INCLUSIVE ROD

Tensile Strength (min)		Yield Strength (at .5% extention under load min)		Elongation (in 2in. or 50mm min, %)	Brinell Hardness (min)	Remarks
Ksi	MPa	Ksi	MPa
65	450	35	240	10	N/A

H06 EXTRA HARD TEMPER

SIZE RANGE: UP TO 1/2" INCLUSIVE ROD

Tensile Strength (min)		Yield Strength (at .5% extention under load min)		Elongation (in 2in. or 50mm min, %)	Brinell Hardness (min)	Remarks
Ksi	MPa	Ksi	MPa
85	585	55	380	6	N/A

SIZE RANGE: OVER 1/2" TO 1" INCLUSIVE ROD

Tensile Strength (min)		Yield Strength (at .5% extention under load min)		Elongation (in 2in. or 50mm min, %)	Brinell Hardness (min)	Remarks
Ksi	MPa	Ksi	MPa
75	515	45	310	8	N/A

SIZE RANGE: OVER 1" TO 1 1/2" INCLUSIVE ROD

Tensile Strength (min)		Yield Strength (at .5% extention under load min)		Elongation (in 2in. or 50mm min, %)	Brinell Hardness (min)	Remarks
Ksi	MPa	Ksi	MPa
75	515	40	275	8	N/A

Alloy	Rating	Density
C65100	30	0.316

	US Customary	Metric
Melting Point - Liquidus	1940 F	1060 C
Melting Point - Solidus	1890 F	1032 C
Density	0.316 lb/in3 at 68 F	8.75 gm/cm3 @ 20 C
Specific Gravity	8.750	8.75
Electrical Resistivity	86.40 ohms-cmil/ft @ 68 F	14.36 microhm-cm @ 20 C
Electrical Conductivity	120 %IACS @ 68 F	0.07 MegaSiemens/cm @ 20 C
Thermal Conductivity	330 Btu · ft/(hr · ft2·°F)at 68F	57.1 W/m · °K at 20 C
Coefficient of Thermal Expansion	9.90 ·10-6 per oF (68-392 F)	17.8 ·10-6 per °C (20-200 C)
Specific Heat Capacity	0.090 Btu/lb/°F at 68 F	377.1 J/kg · °K at 293 K
Modulas of Elasticity in Tension	17000 ksi	117000 MPa
Modulas of Rigidity	6400 ksi	44130 MPa

Joining Technique	Suitability
Soldering	Excellent
Brazing	Excellent
Oxyacetylene Welding	Good
Gas Shielded Arc Welding	Excellent
Coated Metal Arc Welding	Fair
Spot Weld	Excellent
Seam Weld	Good
Butt Weld	Excellent
Capacity for Being Cold Worked	Excellent
Capacity for Being Hot Formed	Excellent