- Bronze Family: Brass
- Tempers: H01 QUARTER HARD, H02 HALF HARD, H04 HARD
- Solids: 3/8" to 2.5" OD
- Hex: 3/8" to 2" OD
- Rectangles: Consult Mill
- Standard Lengths: 144"
- » Download C26000 Spec Sheet (.pdf)
Typical Uses
- Architecture Grillwork
- Automotive Odometer Contacts, Heater Cores, Thermostats, Electrical Connectors, Radiator Cores, Radiator Tube, Radiator Tanks, Tanks
- Builders Hardware Locks, Push Plates, Finish Hardware, Kick Plates, Decorative Hardware, Door Knobs, Hinges
- Consumer Snaps, Planters, Fireplace Screens, Etched Articles, Bird Cages, Coinage, Chain Links, Pen/Pencil Inserts and Clips, Syringe Parts, Watch Parts, Costume Jewelry, Buttons, Shells - Electrical Sockets, Lamps
- Electrical Terminal Connectors, Flashlight Shells, Lamp Fixtures, Reflectors, Screw Shells
- Fasteners Pins, Rivets, Fasteners, Grommets, Eyelets, Screws
- Industrial Air Pressure Conveyer Systems, Sound Proofing Equipment, Springs, Chain, Bead Chain, Tubing for Instruments and Machines, Heat Exchangers, Pump Cylinders, Wire Screens, Pumps, Liners, Power Cylinders
- Ordnance Ammunition Cartridge Cases, Mechanical Housings for Lighters, Shells - Mechanical Housings for Ammunition, Ammunition
- Other Stencils, Washers
- Plumbing Fittings, Bathroom Fixtures, Plumbing Accessories, Faucet Escutcheons, Traps, Plumbing Brass Goods
Similar or Equivalent Specification
| CDA | ASTM | ASARCON | SAE | AMS | Federal | Ingot# | Military | Other Desc |
|---|---|---|---|---|---|---|---|---|
| C26000 | ASTM B927 | J461 | MIL-V-18436 | LEADED COMMERCIAL BRONZE | ||||
| J463 |
Chemical Composition (according to ASTM B927-08a)
| Cu% | Sn% | Pb% | Zn% | Fe% | Ni% | Sb% | P% | S% | Al% | Mn% | Si% |
|---|---|---|---|---|---|---|---|---|---|---|---|
|
Note: Single values represent maximums
|
|||||||||||
| 68.50-71.50 | 0.07 | REMAINDER | 0.05 | ||||||||
Mechanical Properties (according to ASTM B937-08a)
H01 QUARTER HARD TEMPER
SIZE RANGE: 1/2" DIAMETER AND UNDER
| Tensile Strength (min) | Yield Strength (at .5% extention under load min) | Elongation (in 2in. or 50mm min, %) | Brinell Hardness (min) | Remarks | ||
|---|---|---|---|---|---|---|
| Ksi | MPa | Ksi | MPa | |||
| 50 | 345 | 30 | 205 | 20 | N/A | |
SIZE RANGE: OVER 1/2" DIAMETER TO 1" INCLUSIVE
| Tensile Strength (min) | Yield Strength (at .5% extention under load min) | Elongation (in 2in. or 50mm min, %) | Brinell Hardness (min) | Remarks | ||
|---|---|---|---|---|---|---|
| Ksi | MPa | Ksi | MPa | |||
| 48 | 330 | 25 | 170 | 24 | N/A | |
SIZE RANGE: 0VER 1"
| Tensile Strength (min) | Yield Strength (at .5% extention under load min) | Elongation (in 2in. or 50mm min, %) | Brinell Hardness (min) | Remarks | ||
|---|---|---|---|---|---|---|
| Ksi | MPa | Ksi | MPa | |||
| 46 | 315 | 20 | 140 | 28 | N/A | |
H02 HALF HARD TEMPER
SIZE RANGE: 1/2" DIAMETER AND UNDER
| Tensile Strength (min) | Yield Strength (at .5% extention under load min) | Elongation (in 2in. or 50mm min, %) | Brinell Hardness (min) | Remarks | ||
|---|---|---|---|---|---|---|
| Ksi | MPa | Ksi | MPa | |||
| 57 | 395 | 35 | 240 | 15 | N/A | |
SIZE RANGE: OVER 1/2" DIAMETER TO 1" INCLUSIVE
| Tensile Strength (min) | Yield Strength (at .5% extention under load min) | Elongation (in 2in. or 50mm min, %) | Brinell Hardness (min) | Remarks | ||
|---|---|---|---|---|---|---|
| Ksi | MPa | Ksi | MPa | |||
| 54 | 370 | 32 | 220 | 20 | N/A | |
SIZE RANGE: 0VER 1"
| Tensile Strength (min) | Yield Strength (at .5% extention under load min) | Elongation (in 2in. or 50mm min, %) | Brinell Hardness (min) | Remarks | ||
|---|---|---|---|---|---|---|
| Ksi | MPa | Ksi | MPa | |||
| 50 | 345 | 30 | 205 | 25 | N/A | |
H04 HARD TEMPER
SIZE RANGE: 1/2" DIAMETER AND UNDER
| Tensile Strength (min) | Yield Strength (at .5% extention under load min) | Elongation (in 2in. or 50mm min, %) | Brinell Hardness (min) | Remarks | ||
|---|---|---|---|---|---|---|
| Ksi | MPa | Ksi | MPa | |||
| 70 | 485 | 50 | 345 | 10 | N/A | |
SIZE RANGE: OVER 1/2" DIAMETER TO 1" INCLUSIVE
| Tensile Strength (min) | Yield Strength (at .5% extention under load min) | Elongation (in 2in. or 50mm min, %) | Brinell Hardness (min) | Remarks | ||
|---|---|---|---|---|---|---|
| Ksi | MPa | Ksi | MPa | |||
| 65 | 450 | 45 | 310 | 15 | N/A | |
SIZE RANGE: 0VER 1"
| Tensile Strength (min) | Yield Strength (at .5% extention under load min) | Elongation (in 2in. or 50mm min, %) | Brinell Hardness (min) | Remarks | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Ksi | MPa | Ksi | MPa | ||||||||
|
*NOTE FOR SIZES LARGER THAN 2" DIAMETER THE MINMUM MECHANICAL PROPERTIES MUST BE AGREED UPON BETWEEN THE MANUFACTURER AND THE PURCHASER.
|
|||||||||||
| 60 | 415 | 40 | 275 | 20 | N/A | ||||||
Machinability
| Alloy | Rating | Density |
|---|---|---|
| C26000 | 30 | 0.308 |
